Caboose 2 steps with holes. Standard caboose steps, holes in steps. 2” 9” wide. Set of four for one caboose.
Chicago and North Western whistle posts. Four per package. Scaled from CNW drawings.
Old time spoked wheelbarrow. Two per package. Scaled from manufacturer’s drawings.
Caboose 3 steps with tread. Standard caboose steps , <span class="x193iq5w xeuugli x13faqbe x1vvkbs x1xmvt09 x1lliihq x1s928wv xhkezso x1gmr53x x1cpjm7i x1fgarty x1943h6x xudqn12 ...
This item is based on an article in the April/May issue of The S Scale Resource Magazine written by Chris Rooney. These parts will be printed on demand and will take a two week lead time.
In the early 1980’s Alco Models produced a line of very welcome brass diesel models for S scale – specifically 1981 Alco …
Middlesboro, Kentucky’s Harrison Mayes was a coal miner, folk artist, and evangelist. He started dotting the Appalachian landscape with handmade concrete crosses and signs in 1918 …
This is a double Nut/Bolt grab iron end used on many cabooses. See image. May other uses as well such roof top grabs.
The stem is .020 and designed for .015 wire. There are 17 parts per sprue and four sprues per package.
This is a double rivet grab iron end used on many cabooses. See image. May other uses as well such roof top grabs.
The stem is .020 and designed for .015 wire. There are 17 parts per sprue and four sprues per package.
These small parts will really dress up older Athearn/Reynolds/AllNation cars as well as some new cast cars, and of course, your custom built equipment. These represent the square nut that attached a hand grab to older wooden cars. The bolt is a scale 5/8″ with the nut 1/8″.
The stem is .020 and designed for .015 wire. There are 17 parts …
Based on manufacturer’s drawings. You will receive 8 assemblies, enough for two locomotives. They can be bolted onto the locomotive itself or using some type of easy to make bracket. The bracket is up to you. A few bits of brass or styrene, and you’re done.
Not only for modern day homes and business, this will also go nicely with track heaters that are used outside of yards and on the main. Scaled from manufacturer’s drawings.
These wiper blocks were designed for the Central Locomotive Workshop AAR B truck but will find many other uses. Ships with 4 blocks made from a nylon resin. This resin taps and drills, sands, cuts and glues like a dream.
Wipers are not included but we used .003 Hard …
Based on manufacturer’s drawings. You will receive 4 brackets and 16 signal lines. They can be bolted onto the locomotive itself or using some type of easy to make bracket. Most modern locomotives allow for four lines, however, some used three. See the sample photos. Simply cut off one opening and lightly sand. The signal lines are …
Based on manufacturer’s drawings. You will receive 8 lamp assemblies, enough for two locomotives. As seen in the accompanying pictures, they can be bolted onto the locomotive itself or using some type of easy to make bracket. The bracket is up to you. A few bits of brass or styrene and you’re done. Also seen here are models by Brian …
This resin has some flex and will not crack when pressure is applied. These take paint well after priming. We normally use Mr. Primer Surfacer 1000, but any good thin primer will work.
12 pieces per package or enough for 6 cars / locomotives.
<span style="font-family: times new roman, times, ...
This resin has some flex and will not crack when pressure is applied. These take paint well after priming. We normally use Mr. Primer Surfacer 1000, but any good thin primer will work.
12 pieces per package or enough for 6 cars / locomotives.
NOTE: This is NOT offered in black resin because to add any type of rust color to the …
Model Railroad Resource LLC
815.263.2849
Mon - Fri, 8:00-4:00 CST